电话:15685359870
手机:15685359870
QQ:3165088973
邮箱:3165088973@qq.com
地址: 贵州省安顺市西秀区北街街道虹山湖路42号虹山大酒店（百灵.希尔顿逸林酒店 )幢14层9号
DS200DCCAG4A DC power feedback board manufactured by General Electric
DS200DCCAG4A DC power feedback board manufactured by General Electric
DS200DCCAG4A is a DC power feedback board manufactured by General Electric.It is part of the Speedtronic Mark V turbine control system.It no longer receives any kind of support from GE and can be a bit hard to find.AX Control will try to keep it in stock, but please call us directly for DS200DCCAG4A availability.There are many different jumpers available for the DS200DCCAG4A.JP1 is normally disabled, but can be enabled to allow it to write to the EEPROM.JP7 and JP8 are usually not used.JP15 is normally in the enable position enabling the oscillator.JP19 is the water flow input.JP20 is a megawatt input.JP21 is the water flow and megawatt input.JP23 is a direct memory access connection.JP22 is the I/O main oscillator connection.JP31 is the I/O network communication connection.JP32 is a drive system function and only uses 1-2 bits.Jp-33 is a 320 coprocessor oscillator enable connection.JP-34 is a microprocessor timer connection.JP-35 is a 27C1010 or 170 EPROM chip.JP-36 allows 128 or 256K RAM chip selection.DS200DCCAG4A should be installed in a Mark V control cabinet.The cabinet should be used indoors only and should be kept away from liquids and corrosive materials.Should be stored in a clean, dry environment.For more information about the DS200DCCAG4A and its installation procedures, see GE Application Note GEH-6195F.Only trained professionals should attempt to install the DS200DCCAG4A.
DS200DCCAG4A 是通用电气制造的直流电源反馈板。它是 Speedtronic Mark V 涡轮机控制系统的一部分。它不再接受 GE 的任何类型的支持，可能有点难找。AX Control 会尽量保持库存，但请直接致电我们了解 DS200DCCAG4A 的可用性。
DS200DCCAG4A 有许多不同的跳线。JP1 通常被禁用，但可以启用以允许它写入 EEPROM。JP7 和 JP8 通常不用。JP15 通常处于启用振荡器的启用位置。JP19 为水流输入。JP20是兆瓦输入。JP21 是水流量和兆瓦输入。JP23 是直接内存访问连接。JP22 是 I/O 主振荡器连接。JP31 是 I/O 网络通讯连接。JP32 是驱动系统功能，只用到1-2 位。Jp-33 是一个 320 协处理器振荡器使能连接。JP-34 是一个微处理器定时器连接。JP-35是27C1010或170 EPROM芯片。JP-36 允许 128 或 256K RAM 芯片选择。
DS200DCCAG4A 应安装在 Mark V 控制柜中。机柜只能在室内使用，并应远离液体和腐蚀性材料。应存放在清洁、干燥的环境中。有关 DS200DCCAG4A 及其安装过程的更多信息，请参阅 GE 应用手册 GEH-6195F。只有经过培训的专业人员才能尝试安装 DS200DCCAG4A。
